single reed design question

Sardinian “Launeddas” use your “reversed reeds” as well as many other types of small reed pipes, like the Zummara and Shepherd’s Pipes. Here is a close up of Launeddas reeds. Look closely and you will see that some reed tips have been sanded and one has wax added to its tip. This makes tuning much easier.

http://en.wikipedia.org/wiki/File:Launeddas_llengüeta.JPG

I play the sicilian bagpipe which has single cane reeds in both chanters and in all 3 drones. I make and use “inverted reeds.” It was originally mounted with inverted reeds by the Sicilian guy that made the pipe and then I was subsequently taught how to make both regular and inverted. I prefer inverted because I don’t have to pull the reed out of the reedseat to access the bridal. Also if you are using the node of the cane as a back stop to prevent further splitting, I think inverted works best because you dont have to bore out any nodes in the cane or plug any ends up. Another reason is because I have found that sometimes with the regular cut reeds, when you shove them tightly into the reedseat the pressure on the cane can effect the reed vibration or prevent it from vibrating all together.

I have come to the conclusion that the reed does better if left unscraped. perhaps less water-enzyme absorption. it is hard to get that certain tube that won’t need scraping, I have 2 so far. they are less harsh sounding and after some months of playing in are approaching a sweet sound on my Hornpipe.
one of them is sweet :slight_smile: using arundo donax
Tansy

Wasn’t sure whether to start a new thread or not … so here goes.

I’ve been taken by the idea of making a pibgorn :confused:

I’ve found a nice length of naturally seasoned elder, stripped off the bark and cleaned the bore with a plastic scouring pad, so it’s dimensionally “natural” but quite smooth, and drilled a series of 4mm holes using the measurements on Gerald Kikbride’s web-pages. With a whistle-head fitted it plays a scale (more or less, plenty of scope for tuning) but with a home-made reed I can only get the lower three notes before it does a good impersonation of a duck in distress.

I’m using an 8mm bore plastic tube for the reed, wih a plastic blade, as described elsewhere on the web. With a little twine whipping this fits in the bore of the elder nicely. I’ve tried several grades (thicknesses) of plastic blade but end up with either no noise at all or very similar symptoms, albeit in varying pitches, depending on the thickness of the plastic.

I’ve no experience with reed instruments, and only a few weeks with woodwind, so this is all new to me. If these symptoms are recognised, perhaps someone could suggest what measures I might try to achieve a full eight notes.

Thanks in advance
Chris

Try a hair or thin thread under the reed near the clamping O-ring. This will hold the tongue up a little and free it to vibrate rather than block. You can adjust tuning and response by movements of the O-ring and thread - but it will drive you crazy! I’ve had little joy with plastic tube or tongue reeds, not that I’ve given them a huge amount of effort. I’ve done best with elder reeds, though they’re of course very hygroscopic. It’s easy enough to make a cane or elder (or even pen-tube and yoghurt pot) reed that sounds readily out of the pibgorn; getting one to sound in the instrument, in tune across the range and at a regulated pitch is another matter entirely - not too bad if you just want it in tune with itself, but if it needs to be at a set pitch to play with others…

Jem,
Thanks for the encouragement … at least I know it’s supposed to be difficult :smiley:

I’d also tried with a couple of lengths of seemingly appropriate diameter bamboo with no sound at all, and the local phragmites reed-bed didn’t seem to have any material large enough to be useful, so perhaps that leaves an elder reed.

Is it possible you might publish a set of dimensions for a reed that works, so I might scour the countryside for some suitable material?

It did occur to me that my naturally-bored elder may be of unsuitable dimension, in that the hole down the middle is slightly tapered, going from 11mm to 9mm diameter, whereas Gerald Kikbride’s web-page quotes 7mm bore … is this likely to be an issue?

Thanks again,
Chris

I can’t honestly even start to try to answer the last Q from any practical experience, sorry - though in the general nature of these things I wouldn’t expect it to be a make-or-break issue - just might affect tuning or response through the scale etc… but shouldn’t make it impossible to sound.

As for elder reeds, just cut some this year’s long shoots and experiment with c 5cm lengths with on OD of about 6-8mm and wood about 1mm or less thick once de-barked and de-pithed. It’s free, so you can make as many as it takes to get the hang of it! I stop up the outer end with sealing wax and slip a bit of cotton sewing thread under the tongue, and on some I have used a neoprene o-ring as a bridle too - including the one (and only) I currently play with - though as the o-ring tends to go into the reed socket of the body bore on my John Glenydd, keeping all in correct place/making adjustments can be tricky! I made many dozens of both cane (arundo donax) and elder ones before I got one that more-or-less works tolerably consistently once wetted and played in at concert D in the pibgorn.