Hello everyone. It’s been a while since I’ve been on board, but just now getting back into whistle playing - been giving the guitar more focus, but it’s time to get serious again with whistle playing. What are some of the good PVC or the like whistles out there these days? Thanks.
Why not make your own?
Thanks for the link. However, I’m not one with the patience to do such a thing 
I’d much rather buy, and appreciate, the work of others!!
So far I have found Parks Whistles, Susato, and Tony Dixon… are there any others?
PVC whistles, I don’t have any yet, so I can’t comment on them;
Jubilee, by Mr. Daniel Bingamon, Chiff and Fipple member
http://www.tinwhistles.us/jubilee/
Wicked Good Whistles, out of Maine
http://www.whistlesmith.com/
Gonzato(already mentioned) makes and sells whistles, as well as giving DIY instructions.
http://www.ggwhistles.com/models.html
Parks Every Whistle look like winners too.
http://www.parkswhistles.com/
I know I missed some, sorry.
Parks are the best PVC whistles I’ve played…
Susatos are ABS, at least the Kildares.
I’ve a related question.
Of the plastics used for whistles which are the most durable, ABS, PVC, CPVC, Derlin, or others?
Sweetheart, Busman, O’brien, O’dwyer, Milligan. All great Delrin whistles. Delrin must be the toughest. Carey Parks makes great whistles, very similar to Water Weasels IMO (not a surprise there) and CPCV is really tough too.
They can all be quite durable if you look after them and don’t use them as tent pegs. It depends somewhat on the design and to what conditions you are going to subject the instrument.
Delrin and acetal are probably the most durable in terms of heat and chemical exposure. These polymers are commonly used as bearings and such in industrial applications. I like the way it machines too. I have not found a better polymer myself
Polycarbonates (parts of Sweet’s whistles) are used in barriers, windows and shields for ballistics purposes but it can get stress fractures from heat and other exposure. But it holds together well.
ABS as in the Susato Kildare are quite durable just protect the edge of the labium. Some older Susatos were made from ABS with CPVC tubes (I still have one) and they seem to last just as long.
Dixon polymer whistles seem to be more sensitive to heat than most others I have owned. It’s not good to leave them in a warm car during the summer heat. They can warp and go bananas. The banana bend is easily cured with a bath in warm water and a quick roll on a flat surface. But it’s still not the best thing to put the whistle through.
CPVC is used in plumbing and can withstand household hot water temperatures just fine and it lasts a long time. Praise to the Water Weasel Eb, D, C, G and F whistles! So unless parts are machined to be rather thin they will be durable. I’ve put my own homemade CPVC whistles through the dishwasher and they hold up although the thinner parts of the tuning slide and blade can distort a little which might be more from the caustic detergents used in dishwashing than the heat alone. I’ve also
PVC is more brittle than CPVC (IME) and it is a bit more sensitive to heat than the CPVC. Again commonly used in plumbing applications, mostly as drain pipes. I’ve created some unlique sculptures with it on the lathe that were supposed to actually be whistles, gotta watch the turning speed and feed rate. It still can make a good and durable whistle. Again, praise to the Water Weasel Bb and low A whistles.
I’ve also used acylics and didn’t find them particularly durable. It fractures too quickly for my tastes.
I’ve molded whistle parts from polyester resins and it works. It can also fracture under stress.
I’ve tried nylon to make whistles as well. It can be very durable. I just don’t favor machining it myself. It probably would be good for a molded whistle though.
These are just my experiences and are based on the types of plastics I have experience with. There can be many formulations of each type so others may have different experience to mine.
Feadoggie
I’ve got a Shearwater pvc low d whistle (is there a canofworms alert button?) which sounds, I think, not at all dissimilar to the Alba I have recently acquired. I like it.
I don’t think anyone has mentioned Goldfinch (from Poland) - Not at all bad high whistles, though I think the Parks Everywhistle is better.
I have a water weasel that is very good. You can’t buy a new one but from time to time they show up for sale used. I got mine for a ridiculously low price. I like the Every Whistle also. I have no experience with the others.
@Feadoggie - Dude, I was hoping for a comprehensive reply about plastics used for whistles. 
Thanks!
Thanks for the replies and suggestions everyone. I’ll begin looking them all up…
From an old note to me from Mike K. at Susato:
Three makers of pvc/cpvc whistles that haven’t been mentioned: Mack Hoover, Ethnicwind whistles, and Tommy Dion.
Thanks for the info.! Does Mack Hoover make an all cpvc whistle, or just the head joint?
Mack has made whistles entirely of cpvc, but I didn’t notice them on his website when checking last night. However, send him an email and double-check. He’s a wonderful person to talk to and deal with.
Thanks, will do…
i have a dixon dx012 low d and i like it but there is a new one coming from dixon tbx012 for about the same price range. next, Jubilee, by Mr. Daniel Bingamon, Chiff and Fipple member
http://www.tinwhistles.us/jubilee/ i own one of these and they have a woody sound and take a lot of air to play but do play on the easy side. good luck!
www.tuxedomusic.com