OT: Questions about replacing modems

Yes, it looks like you have a Data/Fax/Voice modem in there. You can just unhook to connection to the sound card and remove the card. You may get an error on bootup if the voice software is installed, it may bneed to be removed but it may not if so it’s not hurting anything. Install the new modem, close the case and boot up. Hopefully it will either recognize the modem or ask for a disk. After that you should be good to go. Also, what speed processor do you have? I have a Pentium 200MMX chip floating around that I can give you if it will help you any. I may also have memory that works in this machine. I’ll have to check on that though.
Let me know.
-Jim

Jim,

The Specs on that page are showing that my PC has an AMD-K6 233Mhz chip, although I can’t actually see the chip to verify - must be tucked back under the bottom bottom card that’s installed, or somewhere else I’m not seeing at the moment…

The RAM type required is: 72 PIN SIMM, 60ns-70ns Fast-Page or EDO type DRAM Modules.

Loren

OK, I didn’t see which processor you had already just the switches on what you could go to so I thought you may have been at 166. I’ll check through my spare pile of stuff when I get home and see if I have anything that will work in your PC.
-Jim

Cool, Thanks a million!!!

Loren

Well…

I ran out, did some errands, got can of compressed gas, took the old modem out, and went to put the new modem in only to find that the new modem is mounted at the top of the bracket while the old one is at the bottom, soooo… it’s a no go.

Ah well, at least the inside of my PC is much cleaner now :laughing:

Guess it’s back on with the case and hook up all the wires again…

Thanks again to to everyone for their help and suggestions, it’s been much appreciated.

Loren

On 2002-11-08 10:41, Loren wrote:
Jim,

Thanks man! The model number is 5233LR I had it wrong before.

Loren

http://www.acersupport.com/desktop/

There is a link on that page to tell you where to find the exact model number. I have access to a bunch of old driver CD’s and floppys from different computers if they are needed.

Aodhan

On 2002-11-08 15:38, Loren wrote:
Well…

I ran out, did some errands, got can of compressed gas, took the old modem out, and went to put the new modem in only to find that the new modem is mounted at the top of the bracket while the old one is at the bottom, soooo… it’s a no go.

Ah well, at least the inside of my PC is much cleaner now > :laughing:

Guess it’s back on with the case and hook up all the wires again…

Thanks again to to everyone for their help and suggestions, it’s been much appreciated.

Loren

Loren-

Judging from the pictures in the user guide, the board expansion card should be able to mount your new modem in any position.

However, if you can’t get that, take your new modem back and get an external version. That and some RAM (Ram is one of the best, cheapest performance enhancers out there) should do you up nicely.

Aodhan

Man, unless the socket that the modem card slips into is moveable (I’m joking - it’s clearly not), or I’m missing something really obvious, there’s no way the new card can be used: When the bracket is in place, the board sits a good half an inch or more above the socket…

Loren

On 2002-11-08 16:59, Loren wrote:
Man, unless the socket that the modem card slips into is moveable (I’m joking - it’s clearly not), or I’m missing something really obvious, there’s no way the new card can be used: When the bracket is in place, the board sits a good half an inch or more above the socket…
Loren

Without seeing it, it’s hard to describe…take a look at the bottom of the “external” facing portion of the bracket (The part that is visible at the back of the computer that you can see through the rectangular hole in the computer case). At the bottom of that bracket (on the card) there is a small tongue. Make sure that slides into the hole in the case below the edge of the motherboard. If it doesn’t, then your card appears to ride “high”.

Does your card slot have a card in it going up, that allows you to plug cards onto the card, or are you plugging it directly into a slot on the MB (Motherboard)? :confused:

Aodhan

There is a socket for the modem card that is soldered directly to the motherboard - no card adaptor type thing in that socket.

I checked very carefully earlier, and the bracked lined up fine with the case, both inside and out.

When I say the card is “above” the socket, here’s what I mean: The modem card mounts horizontally, the socket for the protrudes from a vertical board to one side. With the new card in place, the edge of the card that should go into the socket is over a half inch higher vertically than the socket - it’s not horizontally farther away from the socket (like pushing it in farther would help or something along those lines). No, unfortunately the new card is simply mounted to the top of the bracket, rather than the bottom, which is where it needs to be to fit in my PC, darn it.

Thanks though :slight_smile:

Loren

[ This Message was edited by: Loren on 2002-11-08 20:07 ]

On 2002-11-08 12:18, Loren wrote:
Additional info and resources here apparently - haven’t yet checked them out…but will shortly…

http://www.acersupport.com/desktop/aspire/html/v55la2c.html

Loren

Well, After looking through my parts bin, it looks like I don’t have memory for you. The documentation at this link says you can have a maximum of 96MB using 3 32MB DIMMS. I only have 2 64MB DIMMS here. However, I do have a 4.3GB Seagate hard drive I can give you. I’ve just got to wipe it. Where are you Loren? Are you still in the Tri-State area? If you are reasonably near by, I can come out there and take a look at your PC for you and get you running better. Much faster that trying to talk you through stuff online.
Probably not for a couple of weeks though.
Let me know,
-Jim

P.S. Check your private messages, I sent you my contact info.



[ This Message was edited by: Jim_B1 on 2002-11-09 07:41 ]

Loren

We recently upgraded our machines so I have a spare computer: Dell, 600mhz Pentium III, 3D graphics, Turtle Beach Sound Card, tower case, I think 128 MG ram - not sure what else is in there until I open it up. No hard drive or monitor. If this is something you might be interested in, send me an email. I could let you have it very cheap.

Teri

On 2002-11-08 18:57, Loren wrote:
There is a socket for the modem card that is soldered directly to the motherboard - no card adaptor type thing in that socket.

I checked very carefully earlier, and the bracked lined up fine with the case, both inside and out.

When I say the card is “above” the socket, here’s what I mean: The modem card mounts horizontally, the socket for the protrudes from a vertical board to one side. With the new card in place, the edge of the card that should go into the socket is over a half inch higher vertically than the socket - it’s not horizontally farther away from the socket (like pushing it in farther would help or something along those lines). No, unfortunately the new card is simply mounted to the top of the bracket, rather than the bottom, which is where it needs to be to fit in my PC, darn it.

Thanks though > :slight_smile:

Loren

Loren, it sounds like the reason for the misfit is that your new modem is for a PCI slot (the white ones) and your old modem is ISA (the longer, usually black, slots). I see from the User Manual PDF that your system can accomodate 3 cards. The top two slot postions are set up to take either ISA or PCI. If one of the top two cards is plugged into an ISA slot then you could move that card to the bottom position (ISA) and put your modem in the freed up PCI slot. Upon reboot the computer will see the moved card as a new device but since the drivers are already installed it should find them again with no problem. Hope this helps.

Cheers,
David


P.S. Jim, he needs SIMMs not DIMMs

[ This Message was edited by: Feadan on 2002-11-09 10:49 ]

Jim,

Let’s see…The information on memory I’m looking at is here, and based on the pathway that I used to find it, pertains to my PC (although I haven’t downloaded the PDF manual yet.): http://www.acersupport.com/desktop/articles/v55la2c_ram.html

This shows 128MB max via the 4x32MB 72 pin SIMM. I have confirmed visually that there are 4 of these slots - currently loaded with 8 and 16MB SIMM. I’m still wondering what happens if you plug 72 PIN SIMMs with more than 32MB ea. and/or greater than the spec’d 128MB total…

I sent an e-mail in response to your PM by the way.

David,

Thanks for the info on the board/chip, looks like I’m stuck at 233 then.

Interesting about the sockets…The current modem card that I tried to replace is indeed in the 2nd of 3 slots, and it has the black socket, unfortunately the new card just wouldn’t line up because of how it was mounted on the bracket…

Teri,

I’ll contact you off list to get more details, thanks.

Loren

On 2002-11-09 11:35, Loren wrote:
Interesting about the sockets…The current modem card that I tried to replace is indeed in the 2nd of 3 slots, and it has the black socket, unfortunately the new card just wouldn’t line up because of how it was mounted on the bracket…

The point is, Loren, that it isn’t meant to line up with the black slot. That’s why it’s mounted on the other side of the bracket. Even if it did it wouldn’t fit in that type of slot because the architecture is also different for the part that plugs in. It should line up with a shorter white slot. If you don’t have any PCI slots available then maybe we can beg the masses for a used ISA 56K modem for you. The only spare modem I have that is ISA is a 33.6.

Cheers,
David

[ This Message was edited by: Feadan on 2002-11-09 12:59 ]

Sorry David,

I understood most of what you said initially about the different socket types, but I misread one bit and that threw me off.

At this point, it may not be worth trying to upgrade the modem on this machine with something used, because I’d need the associated software, which folks wouldn’t likely have still lying around.

Memory is another issue.

I’m also looking into the details of Teri’s PC, to see if that’s a viable alternative for me.

Thanks for help :slight_smile:

Loren

On 2002-11-09 13:36, Loren wrote:
At this point, it may not be worth trying to upgrade the modem on this machine with something used, because I’d need the associated software, which folks wouldn’t likely have still lying around.

Don’t give up that easily. Many of us geeks have drivers to go with the spare parts we have lying around. If Terri’s machine doesn’t work out there is still hope. Just out of curiosity does your Slot Board (a.k.a. Riser Board) look like this?

Got this from the User Manual on the link you previously posted.

Cheers,
David

[ This Message was edited by: Feadan on 2002-11-09 13:46 ]