My half set leaks

My mainstock is suffering from a air leak in one of the plugs. Now, that would be the “best” place for a leak to be, if it had to be anywhere on my set, right (considerin how a leaky bag would be in comparison)? But how do I fix it? We’re talking about a leak that empties the air about 1/2 as fast as a normal note in the first octave.

Or are Uilleann pipes just supposed to have a leak somewhere? - It comes with the lovely reed problems, tuning issues, gurgling notes and all that? :stuck_out_tongue:

Pull the plug and put a bit more thread on it. And a bit of beeswax.

The plug just seems so very tight. How do I pull it out without damaging anything, and what kind of tool should I use for this operation (hopefully without leaving any marks)?

Usually the holes for the regulators a pre-drilled in the stock and plugged with a wooden plug wrapped in the usual way with waxed thread. I assume this is the case in your set. If there’s a leak it seems to make sense either the plug itself or the thread has shrunk. If you can’t get hold of it strong enough to make it shift maybe see if the plug will move if you tap it from the other side?

Or ye can just stick some tape over the holes when ye remove the stock from the cup (ie the back of the stock ) and leave the plugs alone until ye need to remove them.
Slán Go Foil
Uilliam

I don’t dare attempting to remove the stock. I’ll try and see if I can get out the plug at first.

Your stock should be in the mainstockcup in the same manner as the plug sits in the stock : a waxed thread connection that shouldn’t be much trouble to take out.

If you want to keep your pipes going you will have to maintain them, you can’t do that if you’re afraid to take them apart.

Sure, but it seems like everything is a very tight fit. I’ll try out some disassembling later on.

You can always wait for the Scandinavian winter to dry them out and wait for the bits to fall off

Agree with Peter. Take 'em apart and put 'em back together again. You will learn a lot in the process. It will also give you greater appreciation for the pipemakers work. You probably will not hurt them unless you sit on a piece or attempt to employ it as a tool of sorts.

You should have seen us trying to get Larry’s mainstock free from his old bag. All the pieces weere taken off the stock and all we had to deal with was the bag and the mainstock.We finally had to take a woodworking clamp to the stock and twist the brass ferrulle off the f*****g thing. Took two strong men, a couple of beers- would have been perfect for “how many pipers did it take to take the bag off the mainstock” joke.

My brother left for Ireland once, with his mainstock hemped up very tight for US winter and upon arrival in Co Clare in the spring, his drone switch washer and nut promptly worked themselves off the threaded stem and were rattling about in the mainstock cup. The stocks swelled and would not budge and it took every man jack in the pub and a few gallons of porter to loose it.

In the meantimes if ye are really nervous about taking the thing apart put a bit of wax around the leak :wink: If ye haven’t got beeswax use a bit of the red wax ye can get from the outside of an Edam Cheese.Squeeze it in your hand for a minute or two to soften it and press it into the side of the hole where it is leaking..2 minute job.Then eat the cheese & ye get breakfast or whatever as well.That is my recipe for the day
Slán Go Foill
Uilliam

Before dismantling your pipes it might be worth removing the plug and sealing the hole with bluetack to see if this is where the air is escaping.

If it is then i’m guessing the thread you’ve got on the plug is either on the large side, or just poorly fitted. It is possible to have a very tight fit that leaks especialy if the hole is irregular.

Removing the stock was very easy. Thanks for encouraging me! I understand the structure of this great piece of work now. I got the plug out, and I almost got it perfectly airtight. If I add some more hemp, It’ll be just fine. Thank you for all the help.

I’ll just get kicked off the forum if I reply to this with the obvious response.

Maybe… maybe not. :laughing:

I’d forgotten to check my mainstock bits in the smallening humidity, and found that they came apart very easily. A bit of waxed dental floss, and all’s snug, now. I was wondering why I seemed to be working too hard; there must have been some leakage due to the looser fit, although it wasn’t obviously loose. Much easier to play, now.

'Tis the season for leaks inventory.

OK, I’ll scale it back: Why do people constantly ask for help doing the blatantly obvious much less several exchanges here, without first even trying–for example in this case–just pulling out said plug or pulling out said mainstock. Particularly, as in this case, when had it been tried at all it would have come apart very easily.

So, let me go one more…those are PLUGs. Pull them out. Tools? Have you no fingers? No pliers in Bergen? No butterknives to slip under and work them loose?

Have you never pulled a cork out of a bottle!!!

It’s a plug and you need advice on how to pull out a plug?

You pull it out.

Unfortunately D.E.B. you have totally missed one of the most useful reasons for having this forum - advice !

Many of the members live a long way from other pipers and makers and rely on the forums for help.

It might be obvious to you but if someone is new to an instrument the last thing they will want to do is to start pulling it apart - how many times has it been said on this forum and in the tutor books - only disassemble the pipes if you know what you are doing.

Osterjeks is new to the pipes and is only following this advice. He comes from a part of the world where the nearest pipemaker is a long way away and if he makes a mistake and pulls the wrong part out and wrecks a reed then he is in trouble.

It might be an idea to try and put yourself in the posters position before writing what should be a helpful reply

John

Edited to reword the final remark