Here is a link to another review of a tweaked LBW. The whistle I have tried is not the same whistle. The one I had is #2.
http://chiffboard.mati.ca/viewtopic.php?t=34358&sid=72dc6ecb855708ed7da6a7a8268be4ee
Right away I want to let you know that this is the first formal review I have done. Although I have tried to be as impartial as possible, reviews do tend to be subjective to the likes and dislikes of the person reviewing. Please excuse any errors. Please let me know and allow me to correct them if found. I have tried to use a format similar to Wanderer’s since it seems to get the information across in a very organized manner. I also have had the assistance of Doc Jones with this review. I used him as my expert advisor/player.
Here is a picture of three LBW’s all together:

The first thing you may notice is the difference in total length. Not only is the tweaked LBW a lot longer than the two that are not tweaked (most likely do to the tweaking process), the two stock ones are different lengths as well!!! Quality control at its “best?”
Next is a pic of the head area of the whistles:

This emphasizes the difference in total length and also shows off Avery’s added label. There is also a difference in the stock labels that I assume indicated different manufactuing eras.
An overall view of the tone holes:

A closer view of the upper holes:

and the lower holes:

The holes look quite worked and appear to be rough. They are, however, not rough to the touch during play. Only the upper hole feels a bit rough when specifically rubbed with a finger tip. I think the exposed aluminum was the first thing I noticed when taking the whistle out of the package, especially when compared to the stock whistles on hand. A bit of touchup paint or permanent marker would go a long ways at improving the overall appearance.
Here is the windway entrance:

You can see that some material has been added to the floor of the windway. I believe this is to reduce the size of the hole. This would reduce the air requirement and increase the backpressure. I found both of these conditions to be true.
Now the windway exit:

If you look really closely you can see some material has been added in the space under the exit of the windway. It appears to be some sort of foam. This is apparently similar to the blue tack mod that has been discussed on this forum in the past. It appears to be securely attached and I did not have any difficulty with it coming loose.
And finally a close up of the blade area:

The blade of the tweaked whistle (left) seems to have been modified in some way. I think it has been dulled as there are some fine abrasion marks on and near this area. I had to look really closely to see them though.
Now, what does all of this add up to?
Sound of the whistle:
The whistle is noticably breathier than the stock whistles.
Tuning:
When I played the whistle so that the bell note was in tune and attempted to keep my breath volume and pressure constant up through the scale it liked to stay a bit on the flat side for half the notes and in tune for the rest. I also tried doing this with the stock whistles. The longer of the two seemed to be balanced around being in tune with a few notes being in tune, a couple above and a couple below. The shorter of the two had a similar response as the tweaked whislte, but being on the sharp side of things.
When I tried the same idea starting at B (playing in tune and keeping breath and pressure constant as possible) and coming down the scale, by the time I got to F# it was jumping to the second octive. The stock whistle, while I could tell they wanted to did not do this.
I realize this may be a silly thing to try, but I did and wanted to report the results. All notes were well within range of being blown into tune on all three whistles though. I also think that being on the flat side (for a constant breath) is an advantage of sorts because it is easier to give a little more breath support to bring it in tune than it is to attempt giving less. This works as long as the break to the second octive is not so sensitive.
Cnat:
Using a tuner I attempted to find the optimal fingering for Cnat for each whistle. What I found was that the tweaked whistle was most in tune with a OXXXXO fingering but it was not as strong sounding note as the regular scale notes. The stock whistles seemed to be most in tune with OXXXOX. This fingering produced a note that was closer in quality to the other notes.
But how does it play?
I had my stand-in expert (Doc Jones) play it some about a week ago. He indicated that the tweaked whistle was a bit more stable during play than the untweaked whistles. He noticed the breathiness right off and that put him off. It was too breathy for his (and our) liking. We played the whistles again tonight and at first he had some difficulty with it as it wanted to break into the second octive on him. He was able to get a handle on it and played a couple of tunes with it as well as the stock whistles.
Overall we liked the longer of the two stock whistles better. It was the excessive (to us) breath sound that was the main deciding factor. The longer stock whistle was close enough in tune to be servicable and just sounded better to our ears. Using a “standard” OXXOOOO Cnat was not terribly noticable during play on the stock whistle, but was fairly noticable on the tweaked one.
The shorter of the two stock whistles was playable but requires a bit of attention and was always trying to play sharp with “normal” playing. This whistle would probably be a candidate for a tweak such as this if one really wanted to have it be a better player.